En stock Produit phare
HC-K 6/12-EBUS
HC-K 6/12-EBUS 1636363 PHOENIX CONTACT Contact insert
$127.97USD
114 en stock
Spécifications clés
:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Taper:B16
Largeur:34 mm
Hauteur:47 mm
Informations sur le fournisseur
Produits : 0
Habituellement expédié sous 2 à 3 jours ouvrables
Qualité garantie
Livraison rapide
Support technique
Spécifications techniques
| Paramètre | Valeur |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| Taper | B16 |
| Largeur | 34 mm |
| Hauteur | 47 mm |
| Longueur | 84.1 mm |
| Série | HC-K |
| Général | For HEAVYCON ADVANCE and HEAVYCON housing of type B16/B32, axial connection for 2 mm Allen wrench |
| Application | Power/signal |
| Type de produit | Contact insert with a fixed no. of positions |
| Note de l'assemblée | To ensure correct use, installation in housing with IP54 protection or better is required |
| Courant nominal | 40 A (power contacts) |
| Révision de l'article | 04 |
| Diamètre de contact | 4 mm |
| Matériel de contact | Cu alloy |
| Numérotation des contacts | 1 - 6 (power contacts) |
| Screwdriver blade | 0.5 x 3.5 mm (control contacts) |
| Couple de serrage | 2 Nm ... 2.5 Nm (PE connection) |
| Profil de connexion | 6+12+PE |
| Degré de pollution | 3 |
| Dessin coté | |
| Nombre de positions | 18 |
| Tension de surtension nominale | 8 kV (power contacts) |
| Catégorie de surtension | III |
| Technologie de connexion | Axial screw connection (power contacts) |
| Type de matériau de contact | turned |
| Nombre de contacts de puissance | 6 |
| Tension nominale (III/3) | 690 V |
| Section transversale du conducteur | 2.5 mm² ... 10 mm² (power contacts) |
| Nombre de contacts de commande | 12 |
| Matériau porteur de contact | PC |
| Cycles d'insertion/retrait | ≥ 500 |
| Section de connexion AWG | 12 ... 8 (power contacts) |
| Température ambiante (fonctionnement) | -40 °C ... 125 °C |
| Drill hole distance, horizontal | 77.5 mm |
| Tension nominale des contacts de puissance | 230/400 V |
| Indice d'inflammabilité selon la norme UL 94 | V0 |
| Longueur de dénudage du fil individuel | 8 mm +1 mm (Power 6 mm² ... 10 mm²) |
| Matériau de la surface de contact, contact électrique | Ag |
| Matériau de la surface de contact, contact de contrôle | Ag |
Description du produit
Contact insert, number of poles: 6+12+PE, size: B16, power contacts: 6, control contacts: 12, Female, Axial screw connection, 690 V, 40 A, 2.5 mm² ... 10 mm², application: Power/signal
Caractéristiques principales
- Qualité de niveau industriel
- Conforme RoHS
- Certifié CE
- Garantie d’un an
Documents du produit
Fiche technique
Spécifications techniques et données de performance
Manuel d'utilisateur
Guide d'installation et d'utilisation
