En stock Produit phare
UDPHL113
UDPHL113 DPH-L113 PANASONIC Sensor head DPH-L113 for positive pressure, 0 to 1.0MPa, R1/4 male thread, cable..
$0.00USD
3290 en stock
Spécifications clés
Article:Specifications
Câble:0.2 mm23-core heat resistant cabtyre cable 2 m3.562 ftlong
Remarque:Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃+73.4 ℉.The sensor head can be used independently.
Poids:Net weight : 100 g approx., Gross weight : 150 g approx.
Informations sur le fournisseur
PANASONIC
Produits : 4316
Habituellement expédié sous 2 à 3 jours ouvrables
Qualité garantie
Livraison rapide
Support technique
Spécifications techniques
| Paramètre | Valeur |
|---|---|
| Article | Specifications |
| Câble | 0.2 mm23-core heat resistant cabtyre cable 2 m3.562 ftlong |
| Remarque | Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃+73.4 ℉.The sensor head can be used independently. |
| Poids | Net weight : 100 g approx., Gross weight : 150 g approx. |
| Détails | Sensor head |
| Produit | Head-separated Dual display Digital Pressure Sensor [For gas & liquid] |
| Matériel | Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7) |
| Protection | IP67 (IEC) |
| Accessoires | Connector (e-CON) : 1 pc. |
| Numéro de pièce | DPH-L113 |
| Nom du produit | Head-separated Dual display Digital Pressure Sensor [For gas & liquid] DPC-L100 / DPH-L100 |
| orifice de pression | R1/4 male thread (throttle embeded) |
| temps de réponse | 1 ms or less |
| Numéro de produit | DPH-L113 |
| Tension d'alimentation | 9 to 36 V DC[9 to 32 V DC when using the attached connector (e-CON)] |
| rallonge de câble | Extension up to total 10 m32.808 ftis possible with 0.2 mm2, or more, cable. |
| Humidité ambiante | 35 to 85 % RH, Storage : 35 to 85 % RH |
| Fluide applicable | Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7 |
| Méthode de mise à la terre | Capacitor earth (Enclosure-supply terminal) |
| résistance aux chocs | 1,000 m/s2acceleration in X, Y and Z directions three times each |
| Type de pression | Sealed gauge pressure(Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa. |
| Méthode de connexion | Connector |
| Température ambiante | -20 to +70 ℃-4 to +158 ℉(No dew condensation or icing allowed),\n Storage: -30 to +70℃-22 to +158 ℉ |
| Consommation de courant | 20 mA or less |
| Plage de pression nominale | 0 to +1 MPa |
| résistance aux vibrations | 10 to 2,000 Hz frequency, acceleration 200 m/s2, in X direction for four hours, in Y and Z directions for two hours each(Note): The X, Y, and Z directions are defined as follows : |
| Sortie de tension analogique | Output voltage: 1 to 5 V DC (over rated pressure range)\n Accuracy: ±1.0 % F.S. (at 23 ±2 ℃+73.4 ±35 ℉)\n ±2.0 % F.S. (at -20 to 70 ℃-4 to +158 ℉)\n (including linearity, hysteresis and repeatability) |
| résistance d'isolation | 100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure |
| Réglementation applicable | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) |
| Plage de températures moyennes | -20 to +70 ℃-4 to +158 ℉ |
| tenue en tension | 150 V AC for one min. between all supply terminals connected together and enclosure |
| résistance à la pression | 2 MPa |
Description du produit
Sensor head, positive pressure. 0 to 1MPa. R1/4 male pressure port.
Caractéristiques principales
- Qualité de niveau industriel
- Conforme RoHS
- Certifié CE
- Garantie d’un an
Documents du produit
Fiche technique
Spécifications techniques et données de performance
Manuel d'utilisateur
Guide d'installation et d'utilisation
